Search
The precautions for the main wear-resistant parts of the jaw crusher are as follows:1. Frame installation: The jaw crusher needs to be installed on a concrete base. To effectively reduce vibration and noise, a square piece of hardwoo
The precautions for the main wear-resistant parts of the jaw crusher are as follows:
1. Frame installation: The jaw crusher needs to be installed on a concrete base. To effectively reduce vibration and noise, a square piece of hardwood or rubber should be placed between the crusher frame and the concrete. During installation, the horizontality of the frame is extremely critical and must meet the standards in both the horizontal and vertical directions. In addition, the state of the wooden board between the frame and the concrete cannot be ignored. It must be flat, uniform and stable to ensure the good effect of equipment installation and subsequent operation.
Click here to consult for knowledge about jaw crushers
2. Toggle plate installation: There are several steps to replace the toggle plate of the jaw crusher. To replace the toggle plate of the jaw crusher, you need to operate in sequence. First loosen the spring nut of the horizontal tie rod and remove the spring. Then use a chain or wire to tie the lower part of the jaw plate, and use the lever block to pull the wire to make the movable jaw plate move closer to the fixed jaw plate. At this time, the toggle plate drops and the broken toggle plate can be removed. Then, use the wire to drag the new toggle plate to the installation position, loosen the lever block, and let the toggle plate approach the toggle seat. Finally, reinstall the tie rod and spring, remove the lever block, and complete the replacement.
3. Jaw plate installation: The jaw plate of the jaw crusher is a wear-resistant part that needs to be replaced regularly. The crushing chamber of the crusher consists of a fixed jaw plate and a movable jaw plate. During installation, the tooth plate must be firmly fixed to the front wall of the frame and the movable jaw plate by bolts or wedges. At the same time, special attention should be paid to the fact that the contact surface between the jaw plate and the movable jaw plate of the jaw crusher must be kept straight to ensure efficient and stable operation of the equipment.
Previous: SMP Crusher
Next: SMP Crusher
The precautions for the main wear-resistant parts of the jaw crusher are as follows:1. Frame installation: The jaw crusher needs to be installed on a concrete base. To effectively reduce vibration and noise, a square piece of hardwoo
The precautions for the main wear-resistant parts of the jaw crusher are as follows:
1. Frame installation: The jaw crusher needs to be installed on a concrete base. To effectively reduce vibration and noise, a square piece of hardwood or rubber should be placed between the crusher frame and the concrete. During installation, the horizontality of the frame is extremely critical and must meet the standards in both the horizontal and vertical directions. In addition, the state of the wooden board between the frame and the concrete cannot be ignored. It must be flat, uniform and stable to ensure the good effect of equipment installation and subsequent operation.
Click here to consult for knowledge about jaw crushers
2. Toggle plate installation: There are several steps to replace the toggle plate of the jaw crusher. To replace the toggle plate of the jaw crusher, you need to operate in sequence. First loosen the spring nut of the horizontal tie rod and remove the spring. Then use a chain or wire to tie the lower part of the jaw plate, and use the lever block to pull the wire to make the movable jaw plate move closer to the fixed jaw plate. At this time, the toggle plate drops and the broken toggle plate can be removed. Then, use the wire to drag the new toggle plate to the installation position, loosen the lever block, and let the toggle plate approach the toggle seat. Finally, reinstall the tie rod and spring, remove the lever block, and complete the replacement.
3. Jaw plate installation: The jaw plate of the jaw crusher is a wear-resistant part that needs to be replaced regularly. The crushing chamber of the crusher consists of a fixed jaw plate and a movable jaw plate. During installation, the tooth plate must be firmly fixed to the front wall of the frame and the movable jaw plate by bolts or wedges. At the same time, special attention should be paid to the fact that the contact surface between the jaw plate and the movable jaw plate of the jaw crusher must be kept straight to ensure efficient and stable operation of the equipment.
Previous: SMP Crusher
Next: SMP Crusher
What are the factors that affect the production effect of 200 tons per hour river pebble sand making machine?
What are the inspections before the cone crusher of the stone field crusher is operated?
How much does a large sand making machine cost?
What are the main components of impact crusher
Causes and treatment methods of blockage in impact crusherWhat are the factors that affect the production effect of 200 tons per hour river pebble sand making machine?What are the inspections before the cone crusher of the stone field crusher is operated?How much does a large sand making machine cost?What are the main components of impact crusherCauses and treatment methods of blockage in impact crusher